 | Breaker, Large | Hilti TE3000 | Exceptionally powerful breaker for heavy-duty concrete demolition, asphalt cutting, earthwork, and driving ground rods.- Demolition power comparable to 45 kg air-powered breakers
- Easy to control and transport
- Active Vibration Reduction (AVR) vibration-damped jackhammer with two fully decoupled handles
| - Demolishing reinforced concrete slabs
- Breaking/cutting asphalt in civil road construction, pipe laying and pavement repair
- Removing concrete for structural restoration, slab extension, rebar reinforcement and repair
- Digging, trenching and tamping in rocky, hard clay and other dense earthwork
- Setting ground rods in hard soils for a safer, ladder-free installation of earthing rods (optional TE-H PD Power Driver required)
|
 | Breaker, Mid | Hilti TE2000 | Powerful and extremely light TE-S breaker for concrete and demolition work.
- Very low tool weight combined with high demolition performance for dedicated floor breaking
- T-design for perfect handling in-floor breaking applications.
- Active Vibration Reduction (AVR) make the tool less-tiring to operate
- Detachable supply cord for quick and easy replacement for damaged/broken cords on the jobsite
| - Medium-duty demolition of concrete slabs and foundations
- Removing concrete for rebar connections and utility connections
- Breaking work on concrete or other materials in basements and on patios in residential applications
- Breaking out channels for laying pipe in plumbing applications
|
 | Breaker, Small | Hilti TE1000 | Versatile breaker for demolishing or chiseling floor and occasional wall applications (with universal power cord)
- High versatility – in-line design for floor breaking and ergonomic side handle for occasional wall breaking
- Maintenance-free brushless SR motor and triple-chamber lubrication systems for longer service intervals and tool lifetime
- Exceptionally low tool vibration due to Hilti AVR sub-chassis (Active Vibration Reduction) system
| - Demolishing concrete and masonry at floor level or below waist level
- Renovating floors of all kinds
- Removing tiles, bushing and compacting
- Corrective chiseling, such as adjustments to door and window openings
|
 | Rotary Hammer | Hilti TE70-ATC/AVR | Very powerful SDS Max (TE-Y) rotary hammer for heavy-duty drilling and chiseling in concrete
- Active Torque Control (ATC) stops the tool body from spinning uncontrolledly if the drill bit jams – helping to reduce a common safety hazard
- Active Vibration Reduction (AVR) makes the tool less tiring to use – helping to increase daily productivity
- Optional DRS-Y dust removal system collects up to 95% of dust
| - Hammer drilling in concrete, masonry and natural stone with drill bits 12-150 mm in diameter
- Drilling holes for heavy-duty anchors from 20-40 mm in diameter
- Breaching and demolition with pointed and flat chisels
- Hammer drilling in concrete, masonry and natural stone with drill bits 1/2" - 6" in diameter
- Drilling holes for heavy-duty anchors from 3/4" - 1-3/4" in diameter
|
 | Rotary Hammer | Hilti TE50-AVR | Compact SDS Max (TE-Y) rotary hammer for drilling and chiseling in concrete
- Exceptionally light and versatile SDS Max (TE-Y) rotary hammer
- Low contact pressure for high user comfort
- Active Vibration Reduction (AVR) makes the tool less tiring to use
- Optional DRS-Y dust removal system collects up to 95% of dust
| - Hammer drilling in concrete, masonry and natural stone (possible diameter range 12-55 mm, recommended diameter range 16-32 mm)
- Light to medium-duty chiseling in masonry and concrete
- Drilling penetrations mainly in masonry using percussion core bits (possible diameter range 45-150 mm, recommended diameter range up to 82 mm
|
 | Rotary Hammer | Hilti TE-7-C | Powerful D-grip, triple-mode SDS Plus (TE-C) rotary hammer with chipping function
- Weight according EPTA-Procedure 01/2003: 7.5 lb.
- Working mode: Hammer drilling, Drilling only, Chiseling, Chisel setting
- Hammer drilling diameter range: 5/32 - 1-3/32 in
- Ergonomically designed D-grip for comfortable use over long periods
- Robustly built – engineered for maximum reliability and long life
- High drilling performance
Virtually dustless drilling when used with the DRS-M dust removal system
- Quick-change TE-C Click chuck for versatility and ease of use
| - Drilling and hammer drilling in concrete and masonry
- Corrective chiseling and small channel openings in concrete
- Occasional drilling in wood and steel with optional quick release chuck
- Drilling in concrete in clean areas with integrated Dust Removal System (DRS-M)
- Cutting socket recesses in masonry
|
 | Wet/Dry Vacuum | Hilti VC 150-10 XE | Wet and dry vacuum cleaner with built-in power outlet and 150 CFM suction to comply with OSHA
- Container capacity: 8 gallon (US)
- Dust class: n/a
- Integrated power socket: Yes
Sturdy wet & dry vacuum cleaner for use with all Hilti tools
- Built-in power outlet to run an additional tool directly from the vacuum cleaner – suction starts automatically when the tool does
- Hilti AirBoost automatic filter cleaning technology for consistently high suction (can be switched off for quieter operation and to increase water capacity)
- Robust housing, wheels and accessories to withstand the harshest jobsite conditions
- Optional auto-start available – enables on/off via Bluetooth® remote control
| - Dust extraction from grinding, cutting, slitting, drilling and dry coring tools
- Removing slurry during wet core drilling
- Wet and dry cleaning
|
 | Core Drill w/Vac | Hilti DD 150-U | Versatile diamond coring machine for handheld or rig-based coring from 8-162 mm (5/16 - 6-3/8") in diameter
- Base material: concrete, reinforced concrete, asphalt, masonry
- Operation mode: hand-held or rig-mounted drilling system
- High motor performance and sturdy three-speed gearing for optimum drilling speed
- 360-degree adjustable side handle with integrated dust and water management functions
- Real-time feedback display with digital spirit level, gear selector, power control function, advanced usage statistics and easy-to-understand service messages
- Bluetooth® connectivity to WMS 100 water management system
- Real-time usage statistics analysis via the Hilti Connect app
| - Rig-based wet drilling in concrete for pipe penetrations, cable trays and ducts and for the installation of railings and barriers
- Hand-guided wet drilling for setting large-diameter anchors and reinforcing bars
- Hand-guided dry drilling in masonry for pipe penetrations in plumbing, heating and air conditioning installations and for chimney and stove installation
|
 | Core Drill w/Vac | Hilti DD250 | Advanced heavy-duty diamond drilling tool with optional Cut Assist autofeed unit for coring very small to large diameter holes of 12-500 mm (1/2" - 20”)
- Diameter range: 15/32 - 19-11/16 in
- Base material: Concrete, Reinforced concrete, Asphalt
- Operation mode: Rig-based drilling system
- Air-cooled, heavy-duty drive unit – core drill built for high performance with a sturdy design and convenient controls
- Extremely wide diameter range – four-speed gearing for use with most core bit sizes
- Hole-starting function – low-vibration, low-speed mode to start drilling with large-sized core bits
- Hilti Cut Assist – equips the core drill for fully automated drilling. Starts when surface is detected, then continuously optimizes speed and water flow, even when cutting through rebar. Cut Assist means much higher productivity and more time for other tasks (optional DD AF-CA H autofeed unit required)
- Real-time information display – digital spirit level, gear selector, power control function, detailed usage statistics and easy-to-understand service messages
| - Core drilling penetrations for ducts, pipes and cables
- Core drilling blind holes for setting anchors or post-installed rebar
- Stitch drilling for breaches
- Assisted drilling of large quantities of holes with DD AF-CA H autofeed unit
- Assisted drilling of deep holes and extremely large diameters with DD AF-CA H autofeed unit
|
 | 14" Gas Saw | Hilti DSH-900-X | Versatile rear-handle 70 cc gas saw with auto-choke – cutting depth up to 5" with a 14" blade
- Motor cylinder: 68.7 cm³
- Rated power: 3.5 kW
- Wet or dry operation: Wet and Dry
- The most versatile gas cut-off saw we've ever made – cut up to 5" deep with a 14" blade, and even convert to flush-cut mode
- Easy-start gas saw – unique auto-choke helps to make first-pull ignition the norm, and flooded engines virtually impossible
- Robust – upgraded air filters and re-engineered internal components help the gas saw to deliver uninterrupted, high performance
- Easy self-service maintenance – pre-tensioned belt and virtually unbreakable starter rope help to minimize the saw's maintenance downtime
- Compatible with the DSH-P water pump – feeds water to your gas saw from any source, no pressurization needed
| - Construction work – cutting out openings in brick or concrete walls
- Metalwork – cutting steel profiles, pipes and steel sheets
- Laying paving – cutting curbstones and paving slabs to size
- Masonry work – cutting bricks and blocks to size
- Floor construction – cutting expansion joints in fresh concrete
|
 | 16" Gas Saw | Hilti DSH-900-X | Powerful, easy-start 87 cc gas cut-off saw with auto-choke – max. blade diameter 16” for cutting depth up to 6”- Motor cylinder: 87 cm³
- Rated power: 4.3 kW
- Wet or dry operation: Wet and Dry
- Powerful 16” cut-off saw engineered to make your most demanding cutting work quicker and easier – even floor sawing using the optional DSH-FSC floor cart
- Easy-start gas saw – unique auto-choke helps to make first-pull ignition the norm, and flooded engines virtually impossible
- Durable build – reinforced metal blade guard and longer-lasting internal components help you power through the job with fewer interruptions
- Easier, self-service maintenance – pre-tensioned belt and virtually unbreakable starter rope help to minimize the saw's maintenance downtime
- Compatible with the DSH-P water pump – feeds water to your gas saw from any source, no pressurization needed
| - Road construction – perimeter cutting in asphalt and concrete
- Sewage work – cutting metal, concrete and plastic pipes
- Concrete and masonry construction – cutting expansion joints in fresh concrete and openings in brick or concrete walls
- Laying paving – cutting curbstones and paving slabs to size
- Metalwork – cutting steel profiles, pipes and steel sheets
|
 | 12" Electric Saw | DCH 300-X | Wet and dry electric hand-held diamond cutter – cutting depth up to 120 mm with 305 mm blades- Disc diameter: 12 in
- No load RPM: gear 1: 4900 rpm
- Triaxial vibration value for cutting concrete slab (ah): 5.1 m/s²
- Water kit allows wet cutting, which is 30% faster than dry cutting and virtually dust-free
- Depth gauge – allows full control of the cutting depth in 10 mm steps from 40-120 mm
- Ensures a virtually dust-free job site when used with a compatible vacuum cleaner
- Protection against overheating, overloading and water – prolongs the tool's lifetime and increases the operator's safety when wet cutting
| - Cutting reinforced concrete, granite curbstones, slabs, brick and masonry blocks
- Cutting and extending openings for windows, doors and shafts
- Making preliminary cuts for controlled demolition
|
 | 14" Electric Saw | Husqvarna K4000 | Our Cut-n-Break method is the natural choice when you need to cut deep but want a machine with low tool and maintenance costs. The K 4000 Cut-n-Break enables you to cut as deep as 400 mm from one side. Suitable for flush cutting close to walls and floors as well as for smaller jobs like window openings where you want to avoid overcutting at the corners. | - Cost-efficient unique cut-n-break method allows you to work your way through the material step-by-stepLong body and double cutting blades allow you to make cuts up to 16" deep
- The adjustable blade guard allows close cutting to walls and floors, perfect for flush cutting
- An ergonomically designed rear handle and power cord inlet underneath the handles enables ease of use and comfortable handling with hassle-free operation
- The new pop-up carbon brushes protects the collector from unforseen rotor changes which increases reliability and enables longer service intervals
- A powerful electric cutter for both indoor and outdoor use
- "Pulling" rotation: the blades on Husqvarna electric cutters rotate forward, cutting into the material efficiently, minimizing the risk of sticking and kickbacks
- Advanced electronic overload protection varies the rotation speed to warn of approaching overload
- The wet cutting kit with water adjustment gives efficient dust management and makes operation easier and more efficient
- Great for: blocks, curbstones, pavers, cast concrete, deep cutting, floors, walls, grooves, pipe trenches, and pipes
|
 | 12"-20" Gas Road Saw | Husqvarna FS400 Push Saw | Our robust FS 400 LV is a convenient all-round petrol push floor saw. The adjustable handle ensures an ergonomic working position. Perfect weight distribution gives excellent stability while sawing. Ideal for small road repair jobs in concrete or asphalt, up to 189 mm cutting depth. | - Productive and robust with excellent weight distribution and stability making easy to operate
- Adjustable handles provide a closer and more comfortable position to the cutting side for easier alignment and straighter cuts
- Compact saw that is easy to lift
- Large integrated water tank, with quick connection for water hose to the blade guard. No tools requires for dis-assembly
- Low vibration engine and blade shaft mounting system increases comfort and gives excellent cutting performance
- Clear depth indicator adjustable for all blade diameters
- The retractable handwheel can be folded when moving the saw to avoid breakage
|
